A problem has been detected and windows has been shut down to prevent damage
to your computer.

DRIVER_IRQL_NOT_LESS_OR_EQUAL

If this is the first time you've seen this stop error screen,
restart your computer. If this screen appears again, follow 
these steps:

Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any windows updates you might need.

If problems continue, disable or remove any newly installed hardware 
or software. Disable BIOS memory options such as caching or shadowing.
If you need to use Safe Mode to remove or disable componets, restart
your computer, press F8 to select Advanced Startup Options, and then
select Safe Mode.

Technical information:

***  STOP: 0x000000D1 (0x4A8DFDE0,0x00000002,0x00000001,0xF755F0F)

***  NDIS.sys - Address F7544F0F base at F752C000, DateStamp 41107ec3

その中で、環境にやさしく、つまり周りの人がおどろかないように 緑色に塗る、ということが書いてあって、読んで良く分らなかった。 しかし写真を見ると、塩ビパイブは白のようである。確かに白そのまま だと、緑の中では目立つかも知れない。

いますぐには示せないが、もう一つやはり同じ材料を使う記事が あったが、それも白だった。日本だったら灰色に決っていると思うの だが。

# Set the range of port number which will be used for the passive data port
portrange all 50000 50010

May 21 10:50:33 kurobsd ftpd[18536]: /etc/ftpd.conf line 5: maxport `50010 ': illegal number

# Set the range of port number which will be used for the passive data port
portrange all 50000 50009

First of all, the model I am struggling with, is TS-RH2.0TGL/R5

The one important thing is the serial console is enabled by pushing special red button at the same time you push the power button (The red button is sitting in the panel, you will find it by opening front cover, hidden below LCD display).

I have the

Booting from Device 1 
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0 
switched to TFTP boot.
<<system_bootend>>
Hit any key to stop autoboot:  0 
Marvell>>

The first problem was that (1) raidctl -iv hang. It is Ram-disk environment. Control-T doesn't work. And there is no way to know what is happening, the only way to stop is 'Power On Reset'.

So I decided to install everything / on wd0a without RAID setup.

Everything goes smoothly. I needed to swap kernel from ram-disk version to normal kernel to boot. While booting with normal kernel, it detects the trace of RAID5 setup. and it claims problem reading RAID5.

So I have booted ram-disk version again and trying to un-configure by 'raidctl -u raid0'. But it again freezes.

One thing I have to try wipe out the trace of RAID,

dd if=/dev/zero of=/dev/rwd0a count=63

I remember I have typed /dev/null instead of /dev/zero ... BAD .. I have typed following for this time.

# dd if=/dev/zero of=/dev/rwd0c count=63

# disklabel -R wd0 /tmp/ss
disklabel: ioctl DIOCWDINFO: No disk label on disk;
use "disklabel -I" to install initial label

# disklabel -iI /dev/rwd0c
partition> W
Label disk [n]? y
Label written
partition> Q
# disklabel -R wd0 /tmp/ss

(set-face-font
 'default
  "-misc-fixed-medium-r-normal-*-14-*-*-*-*-*-iso8859-1")
(set-fontset-font
(face-attribute 'default :fontset) 
 'japanese-jisx0208
 "-misc-fixed-medium-r-normal-*-14-*-*-*-*-*-jisx0208.1983-0")

;; 上に更に追加して、次のような行を加えると、日本語(記号)は全角で、
;; ただし露語は半角で、とすることが出来る。
(set-fontset-font
(face-attribute 'default :fontset)
 'koi8-r
  "-misc-fixed-medium-r-normal-*-14-*-*-*-*-*-iso8859-1")

May 10 02:00:01 bwg3 lmtpunix[20006]: FATAL: failed to mmap cache file
May 10 02:00:02 bwg3 lmtpunix[21828]: IOERROR: mapping cache file for user.makoto.bounce-spam2: Cannot allocate memory

rm -rf           /var/spool/imap/user/makoto/bounce-spam2
mkdir            /var/spool/imap/user/makoto/bounce-spam2
chown cyrus.mail /var/spool/imap/user/makoto/bounce-spam2

 bounce-spam2/cyrus.index
 bounce-spam2/cyrus.cache
 bounce-spam2/cyrus.header

そう言えば reconstruct(8) という手があったかな、→ /usr/pkg/cyrus/bin/reconstruct

 build.sh command: ./build.sh tools
 build.sh started: Tue May 12 10:46:00 JST 2009
 NetBSD version:   5.0_STABLE
 MACHINE:          evbarm
 MACHINE_ARCH:     arm
 Build platform:   NetBSD 5.0_STABLE evbarm
 HOST_SH:          /bin/sh
 No /export/src-5/tooldir.NetBSD-5.0_STABLE-evbarm/bin/nbmake, needs building.
 Bootstrapping nbmake
 TOOLDIR path:     /export/src-5/tooldir.NetBSD-5.0_STABLE-evbarm
 DESTDIR path:     /export/src-5/destdir.evbarm
 RELEASEDIR path:  /export/src-5/releasedir
 Created /export/src-5/tooldir.NetBSD-5.0_STABLE-evbarm/bin/nbmake
 makewrapper:      /export/src-5/tooldir.NetBSD-5.0_STABLE-evbarm/bin/nbmake-evbarm
 Updated /export/src-5/tooldir.NetBSD-5.0_STABLE-evbarm/bin/nbmake-evbarm
 Tools built to /export/src-5/tooldir.NetBSD-5.0_STABLE-evbarm
 build.sh ended:   Tue May 12 13:54:04 JST 2009

pts/1:makoto@t-105 11:02:36/090508(/export/src-kurobox-arm-5)> \
time sudo ./build.sh -m evbarm -j 8 release > & ../log-kurobox-arm-5-release-2
Password:
10532.207u 1610.023s 1:00:30.22 334.4%  0+0k 9700+2118158io 6372pf+0w

   117  23:10   cvs -Q -d /e/cvsync/cvsync co -r netbsd-5 src
   121  0:23    mv src src-kurobox-arm-5
   122  0:24    cd src-kurobox-arm-5
   123  0:24    cvs -q update -dP
   124  9:17    patch -s -p0 < ../orion_nas/orion_nas-20081107.diff
   129  9:20    vi distrib/sets/lists/man/mi.rej
   130  9:22    tar zxf ../orion_nas/orion_nas-20081107.tar.gz
   264  9:25    foreach i ( /bin/ls ~/public_html/diary/attach/2009/20090504-kurobox-patch-? )
		patch -s -p0 < $i
		end
   131  9:25    emacs distrib/utils/sysinst/arch/evbarm/msg.md.es
   140  10:59   cp -p ~/public_html/diary/attach//2009/20090504-kurobox-KUROBOX_*_INSTALL \
		sys/arch/evbarm/conf/
   148  11:00   pushd sys/arch/evbarm/conf/
   150  11:00   mv 20090504-kurobox-KUROBOX_TERA_INSTALL KUROBOX_TERA_INSTALL
   151  11:01   mv 20090504-kurobox-KUROBOX_PRO_INSTALL KUROBOX_PRO_INSTALL
   153  11:01   popd
   161  11:02   time sudo ./build.sh -m evbarm -j 8 release > & ../log-kurobox-arm-5-release-2

                     INDEX VALUES            
TEST BASELINE     RESULT      INDEX

Dhrystone 2 using register variables        116700.0   426619.0       36.6
Double-Precision Whetstone                      55.0        4.3        0.8
Execl Throughput                                43.0       61.4       14.3
File Copy 1024 bufsize 2000 maxblocks         3960.0    24039.0       60.7
File Copy 256 bufsize 500 maxblocks           1655.0     7865.0       47.5
File Copy 4096 bufsize 8000 maxblocks         5800.0    20908.0       36.0
Pipe Throughput                              12440.0    46481.6       37.4
Pipe-based Context Switching                  4000.0     3234.9        8.1
Process Creation                               126.0      111.0        8.8
Shell Scripts (8 concurrent)                     6.0       18.3       30.5
System Call Overhead                         15000.0    38208.3       25.5
                                                                 =========
     FINAL SCORE                                                      18.5

＠ compare plot versus KUROBOX/HG:

＠ Specs::

Marvell>> setenv bootargs_root root=/dev/mtdblock2 rw panic=5
Marvell>> setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver)
Marvell>> setenv bootcmd 'nboot $(default_kernel_addr)  0 $(nand_uImage_offset)
Marvell>> setenv bootcmd 'nboot $(default_kernel_addr)  0 $(nand_uImage_offset) ;
	setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver); 
	bootm $(default_kernel_addr)'
Marvell>> setenv nand_boot yes

Without saveenv, the next time above setting will be gone.

(7) PROBLEM
* Can't Boot stand alone for now.
Currently bootp server is necessary. Ext2fs and uImage may be one of the work around.

1. Have Native Linux partition (131 = 0x83) by using fdisk
2. By using mkfs.ext2 from pkgsrc/e2fsprogs, make file system

   /usr/pkg/sbin/mkfs.ext2 /dev/wd0h
   

3. place netbsd-arm.bin (by objcopy -O binary) under its ext2fs partition
4. (in u-boot environment) set bootcmd variable as

    setenv bootcmd 'ide reset; ext2load ide 0:4 8000 /netbsd-arm.bin; go 8000'
   

   (saveenv to save above setup permanently after the setup confirmed correct.)

The first of all, I selected 'Use the Entire disk' at original sysinst installation. The last partition was for /export and I might have newfs even after installation to make room for small boot area. So I decided to divide the last partition into /export and another fdisk area.

...
total sectors: 156301488
...
#        size    offset     fstype [fsize bsize cpg/sgs]
 a:   2015937        63     4.2BSD   1024  8192     0  # (Cyl.      0*-   1999)
 b:   2016000   2016000       swap                     # (Cyl.   2000 -   3999)
 c: 156240000         0     unused      0     0        # (Cyl.      0 - 154999)
 e:  14112000   4032000     4.2BSD   2048  8192     0  # (Cyl.   4000 -  17999)
 f:  10080000  18144000     4.2BSD   2048  8192     0  # (Cyl.  18000 -  27999)
 g: 128016000  28224000     4.2BSD   2048  8192     0  # (Cyl.  28000 - 154999)
 h:     61488 156240000     4.2BSD      0     0     0  # (Cyl. 155000 - 155060)

  156301488	original size of 'c'
-     61488	room for fdisk #3
  ---------
  156240000	the size of 'c' after shrink

kuroarm# fdisk wd0
fdisk: Cannot determine the number of heads
Disk: /dev/rwd0c
NetBSD disklabel disk geometry:
cylinders: 155061, heads: 16, sectors/track: 63 (1008 sectors/cylinder)
total sectors: 156301488

BIOS disk geometry:
cylinders: 1023, heads: 255, sectors/track: 63 (16065 sectors/cylinder)
total sectors: 156301488

Partition table:
0: NetBSD (sysid 169)
    start 63, size 156239937 (76289 MB, Cyls 0-9725/124/63), Active
1: <UNUSED>
2: <UNUSED>
3: Linux native (sysid 131)
    start 156240000, size 61488 (30 MB, Cyls 9725/125/1-9729/80/63)
First active partition: 0
kuroarm# 

kuroarm# mount -t ext2fs /dev/wd0h /mnt
kuroarm# ls -l /mnt
total 9941
drwx------  2 root    wheel    12288 May  6 19:09 lost+found
-rwxr-xr-x  1 makoto  wheel  5061572 May  4 17:26 netbsd-arm.bin
kuroarm# 

boot device: <unknown>
root device: wd0a
...
init path (default /sbin/init):  (Return)

＠ pkgsrc related::

kuroarm# cd /export/pkgsrc/pkgtools/digest/
kuroarm# make
===> Skipping vulnerability checks.
WARNING: No /var/db/pkg/pkg-vulnerabilities file found.
WARNING: To fix run: `/usr/sbin/download-vulnerability-list'.
===> Configuring for digest-20080510
=> Modifying GNU configure scripts to avoid --recheck
=> Replacing config-guess with pkgsrc versions
=> Replacing config-sub with pkgsrc versions
=> Replacing install-sh with pkgsrc version
configure: WARNING: If you wanted to set the --build type, don't use --host.
    If a cross compiler is detected then cross compile mode will be used.
checking build system type... ./config.guess: 772: Syntax error: Missing `)'
configure: error: cannot guess build type; you must specify one
*** Error code 1

Stop.
make: stopped in /export/pkgsrc/pkgtools/digest
*** Error code 1

Stop.
make: stopped in /export/pkgsrc/pkgtools/digest
kuroarm# 

export PKG_PATH=ftp://ftp.jp.netbsd.org/pub/pkgsrc/packages/NetBSD/arm/5.0/All
pkg_add digest

＠ Suggestion for sysinst:

• (-1) Get KuroBox Pro
• (0) Get serial console at the bottom (115.2kbps) USB like connector. (See photo below, click enlarges).
• (1) Getting src with kiyohara version.

   cd /export
   mkdir orion_nas
   cd orion_nas
   wget ftp://ftp.jp.netbsd.org/pub/NetBSD/misc/kiyohara/orion_nas/orion_nas-20081107.diff
   wget ftp://ftp.jp.netbsd.org/pub/NetBSD/misc/kiyohara/orion_nas/orion_nas-20081107.tar.gz
  

  The shell commands issued are:

  pts/1:makoto@t-105 9:50:03/090403(/export/src)>
  cvs -Q -d ${REPOSITORY} co -D 20081107 src && cd src && cvs -Q update -dP .
  patch -s -p0 <  ../orion_nas/orion_nas-20081107.diff 
  tar zxf ../orion_nas/orion_nas-20081107.tar.gz 
  time sudo ./build.sh -m evbarm -j 4 release > & ../log-release
  9239.373u 1268.966s 56:42.20 308.8%     0+0k 4311+1844659io 5685pf+0w
  

  By this build, the kernel KUROBOX_PRO KUROBOX_TERA are not automatically build. So build kernel manually.

  pts/0:makoto@t-105 17:23:23/090504(/export/src)> \
  time sudo ./build.sh -j 8 -m evbarm \
  -T /export/src/tooldir.NetBSD-5.0_BETA-i386 \
  kernel=KUROBOX_PRO > & ../KUROBOX_PRO-log
  

  Here I've got an error like:

  src/sys/arch/arm/marvell/if_oriongbe.c:504: error: 'status' undeclared (first use in this function)
  

  Edit the file

  src/sys/arch/arm/marvell/if_oriongbe.c 
  

  and adding the line 462:

  455 static int
  456 oriongbe_intr(void *arg)
  457 {
  458         struct oriongbe_softc *sc = arg;
  459         struct ifnet *ifp = &sc->sc_ethercom.ec_if;
  460         uint32_t ic, ice;
  461         int claimed = 0;
  462         int status = 0;
  

  With this change, the kernel is built, and
• (1-2) Prepare bootp/tftp server and place kernel with -O binary version. Power on the KUROBOX_PRO and interrupt twice when booting: Then issue:

  bootp 8000; go 8000
  

  it runs to the point asking device file.
• (1-3) Then I've got the changes to enable sysinst kernel.
  Changed:
  etc/etc.evbarm/Makefile.inc
  distrib/evbarm/instkernel/instkernel/Makefile
  distrib/utils/sysinst/arch/evbarm/md.h
  distrib/utils/sysinst/arch/evbarm/
  (above four tar + gzipped) 20090504-kurobox-patches.tar.gz
  Added:
  sys/arch/evbarm/conf/KUROBOX_PRO_INSTALL
  sys/arch/evbarm/conf/KUROBOX_TERA_INSTALL
• (2) Again, build release:
  time sudo ./build.sh -j 8 -m evbarm release
• (3) gunzip the kernel (netbsd-KUROBOX_PRO_INSTALL.bin) and put it on bootp server:
  Do the same thing on (1-2):
• (4) sysinst now starts. You may select NFS or FTP depending on your server convenience:
• (5) Replace install kernel by normal kernel on bootp server:
• (6) and boot as

      bootp 8000; go 8000
  

  This should run upto regular multi-user environment.
• (7) PROBLEM
  • Can't Boot stand alone for now.
    Currently bootp server is necessary. Ext2fs and uImage may be one of the work around.
    Related ? (ftp://ftp.jp.netbsd.org/pub/NetBSD/misc/kiyohara/tmp/u-boot-mkimg.sh)
  • NFS client may have a problem.

         cvs -D /NFSserver/hoge co pkgsrc
    

    may soon hang up to some point. Control-T will say: load: 0.00 cmd: cvs 333 [uvn_fp2] 0.51u 8.70s 0% 2440k
  • Reboot won't make it: It won't proceed after following line displayed.

           Orion1   CPU =  Low  
    

  • halt -p halts, but won't power off.

    ---------------------------
    syncing disks... done
    unmounting file systems...
    unmounting /dev/pts (ptyfs)...
    unmounting /kern (kernfs)...
    unmounting /export (/dev/wd0g)...
    unmounting /mnt/var (/dev/wd0f)...
    unmounting /usr (/dev/wd0e)...
    unmounting / (/dev/wd0a)... done
    The operating system has halted.
    Please press any key to reboot.
    ---------------------------
      pressing key here does not proceed after following line:
    ---------------------------
    rebooting...
    Orion1   CPU =  Low 
    ---------------------------
    

• (8) binary and source
  I have placed the binary and source at:
  (ftp://ftp.ki.nu/pub/NetBSD/snapshot/20081107/evbarm/)
  (ftp://ftp.ki.nu/pub/NetBSD/snapshot/20081107/source/)

ヘンデル/ストコフスキ-:  「メサイア」よりパストラル・シンフォニー
ヘンデル              :  合奏協奏曲  作品 6-12
ヘンデル/ハーティ    : 管弦楽組曲  「水上の音楽」

東京都交響楽団
小泉和裕 (指揮)

さて邦題であるが、娘と言っても daughter ではない。 「西部の娘」は La Fanciulla del West で、この時にはこの邦題で誤解はない と思うが、普通に人の名前の後に娘と書くと daughter の意味になる。 つまり何が言いたいかと言うと、 「プッチーニと娘」は適切でなく、誤解 を生む(中身を表わしていない)と思う。「プッチーニと女」というしかないと 思う。女達ではなさそうなので。
www.lafanciulla.com には、次のような説明がある:

La Fanciulla（ラ・ファンチュッラ）とはイタリア語で『いたずらっこ』という意味の言葉です。しかし、子供への愛情のこもった呼びかけにも使います。また、恋人や婚約者への呼びかけに使うこともあり、優しい響きを持った言葉の一つ。